PSMA2000

The basic requirement for obtaining correct results from tensile tests on sheet metal is the specimen itself, correct dimensions, finished surface at the edges and correct preparation in general without affecting the mechanical properties of the tensile specimen. Punching is the most effective and economical method of specimen preparation when it is possible to quickly and effectively remove the work-hardened zone / edge damage from the specimen. The PSM 2000 sheet metal tensile testing machine (well known since 1970) has been redesigned to meet this requirement perfectly and quickly. The machine is so easy to use that even an unskilled worker can produce high quality specimens after a few minutes training. The specimens are perfectly parallel in gauge length (within 0.02mm parallelism). The grinding process takes less than 2 or 3 minutes (depending on the type of specimen). The quality meets and complies with the requirements of all testing standards (ISO 6892-1 / ASTM E370, JIS ...) and the IDDRG (International Deep Drawing Research Group). The machine is under continuous improvement and we are currently building the fifth generation.

The grinding belt is tensioned by a pneumatic system. This increases the comfort and also the reliability of the grinding parallelism. PSM2000 the synonym for highest quality in tensile specimen preparation. Suitable for blanked specimens and also for specimens cut by laser, water jet, milling and others. The machine is equipped with an industrial quality abrasive belt of 2000 mm length. The grinding speed of the belt corresponds to the speed required for the grinding process on metal (15 metres per second) and has a large surface for the grinding consumables (surface 2000 mm in length x 100 mm in width = 200,000 mm²). For special requirements, we are able to supply special abrasive belts with cooling function or for special materials such as titanium, stainless steel, carbon steel and more. Some of our customers also use aluminium oxide abrasive paper to enable this machine to be used for sample grinding for spectral analysis (so as not to contaminate the metal with carbon from the SiC paper).

 

FR-X SERIES

Obtained the supreme precision and overwhelming reliability by the adoption of entirely new designing and precision manufacturing with no compromise!

 

EMPHASIZED HIGH PRECISION

Reviewed the popular FR-e series and achieved the supreme precision.

 

STRENGTHENED BODY

Achieved the remarkable improvement of hardness measurement by the adoption of newly designed strong body.Prepared the maximum stroke of specimen of 255mm and long type of 401mm. (from the horizontal anvil to X3 and X3L)

 

STABLE LOADING AXIS MECHANISM

Adopted highly sensitive load shaft to prevent the side shift by the introduction of ball guide at the top and bottom. The stable measurement of hardness has become possible for the cylindrical and spherical surface.

 

STANDARD COMPENSATION FUNCTION

Low, middle, high compensation of multiple points to meet the each standard. Obtain the test result which is comply with the different standard for all hardness range.

 

SHAPE COMPENSATION FUNCTION

Obtain the test result which is comply with the standard by entering the diameter of spherical surface & cylindrical specimen.

 

DISPLAY OF MAX.DEPTH OF INTENDER

• Display the max.depth of indenter together with test result.
• Be able to evaluate the elastic amount of different sample in hardness value.

 

STEALTH TYPE DOUBLE INFORMATION PANEL

• isplay the various information of OK / NO judgement and conversion and at the same time,display the measurement results.(Load and release of the test load, and hardness indication are automatic)

 

FUNCTION OF DATA JUDGEMENT

• Display the judgement of measurement data (HI, OK, LO), if you set the maximum value and minimum one and the mean value, if you set measurement point on the sub-information panel.

 

LED LIGHT 

• Obtained the supreme visibility of specimen in the dark environment and achieved the minute positioning.

 

USB DATA OUTPUT

• USB (B2.0) connector is equipped. USB data can be transferred to PC.(Option) Capable in compliance with all ASTM (E-140), SAE (J-417b).

 

PSM 2000

The basic requirement for obtaining correct results from tensile tests on sheet metal is the specimen itself, correct dimensions, finished surface at the edges and correct preparation in general without affecting the mechanical properties of the tensile specimen. Punching is the most effective and economical method of specimen preparation when it is possible to quickly and effectively remove the work-hardened zone / edge damage from the specimen. The PSM 2000 sheet metal tensile testing machine (well known since 1970) has been redesigned to meet this requirement perfectly and quickly. The machine is so easy to use that even an unskilled worker can produce high quality specimens after a few minutes training. The specimens are perfectly parallel in gauge length (within 0.02mm parallelism). The grinding process takes less than 2 or 3 minutes (depending on the type of specimen). The quality meets and complies with the requirements of all testing standards (ISO 6892-1 / ASTM E370, JIS ...) and the IDDRG (International Deep Drawing Research Group). The machine is under continuous improvement and we are currently building the fifth generation. The grinding belt is tensioned by a pneumatic system. This increases the comfort and also the reliability of the grinding parallelism. PSM2000 the synonym for highest quality in tensile specimen preparation. Suitable for blanked specimens and also for specimens cut by laser, water jet, milling and others. The machine is equipped with an industrial quality abrasive belt of 2000 mm length. The grinding speed of the belt corresponds to the speed required for the grinding process on metal (15 metres per second) and has a large surface for the grinding consumables (surface 2000 mm in length x 100 mm in width = 200,000 mm²). For special requirements, we are able to supply special abrasive belts with cooling function or for special materials such as titanium, stainless steel, carbon steel and more. Some of our customers also use aluminium oxide abrasive paper to enable this machine to be used for sample grinding for spectral analysis (so as not to contaminate the metal with carbon from the SiC paper).

 

LC-200R/LC-200RB Series

Versatile Function, Peerless Advanced Technology Mainstream of Rockwell Method in the New Century

DIRECT LOADING METHOD WITH LOAD-CELL FEEDBACK INSTEAD OF WEIGHT SYSTEM & DIRECT LINEAR DISPLACEMENT MEASUREMENT.

High Speed Test Cycle and Extremely Accurate Loading Control based on Intelligent Software come true.

ULTIMATE IN FLEXIBILITY CONFORMING TO VARIOUS REQUIREMENTS BY ISO,JIS, ASTM. ETC.

USER-FRIENDLY ONE-TOUCH OPERATION ON VIVID 8-COLOR TOUCHPANEL FOR DISPLAY AND INPUT ALL TEST CONDITIONS.

ONE TESTER, ALL ROCKWELL SCALES, REGULAR & SUPERFICIAL, AND LIGHT LOAD BRINELL TEST INSTANTLY AVAILABLE WITH THE TOUCH OF A FINGER.

In addition to all Standard Rockwell Test Loads, the LC-200R Series allow User Selection of Minor/ Major Load Combination (anywhere between 3 and 200 kgf) allowing Creation of Customized Rockwell Type Test - Ideal for Research Application.

ENTIRE TEST CYCLE WILL BE PERFORMED FULL-AUTOMATIC.

Descent of Load Shaft ～ Minor Load Application ～ Test Load Application/Hold/ Release ～ Hardness Display ～ Ascent of Load Shaft

 

8 LANGUAGES AVAILABLE

Japanese/ English/ German/ French/ Italian/ Spanish/ Chinese/ Korean

 

DETECTION AND OUTPUT OF [MAX. INDENTATION DEPTH] POSSIBLE.

• This Function is very Effective to provide Precious Data for Evaluation of [Fracture Toughness] of Fine Ceramics and Compound Materials.(LC-200RB)

VARIOUS DATA CORRECTION AVAILABLE 

• Max. Five Points on HR/ Offset on each HR/ HR on Convex Cylindrical Surface (ASTM)/ HRC on Convex Round Surface(JIS)

MAX. 2000 DATA MEMORY CAPACITY. 

• Obtained the supreme visibility of specimen in the dark environment and achieved the minute positioning.

 

VARIOUS DATA EDITING & STATISTICAL FUNCTION AVAILABLE.

• Data Editing/ Statistic Data (Test Times/ Max./ Min./ Mean/ Range/ Standard Deviation/ Dispersion/ Coefficient of Variation)/ Graph Chart Display/ Histogram Display